AOR AR8200 Spezifikationen Seite 34
- Seite / 142
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
34
Access the STEP menu using the key sequence
. Use the main dial to select a step size of
20 kHz (do NOT press enter!).
to access the STEP-ADJUST menu.
Accessing this menu will activate the step-adjust
facility, the “ADJ” legend will be displayed on the
LCD to confirm selection. You will note that the
calculated step adjust value is displayed on the
bottom of the LCD as “ADJ+ 10.00” representing a
positive offset of +10 kHz with a step size of 20
kHz. to accept the displayed
data.
The display will return to VFO mode with 148.010
MHz displayed. The main dial will now correctly
follow the required bandplan.
3-9-2 Cancelling step-adjust
There are two ways to cancel step-adjust
1. Access the STEP menu. , the step-adjust data will be
immediately displayed along with step size. to remove the step-adjust data
from the display, the “ADJ” legend will be removed from the LCD. to accept
the changes. Step-adjust will be cancelled.
2. Presuming that you have manually selected step-adjust (step-adjust has not been set by the
auto-mode bandplan), re-select AUTO-MODE which will reinstate the auto-mode step size, step-
adjust, frequency offset and receive mode. . The “ADJ” legend
will be removed from the LCD and the auto-mode “AUT” legend will be displayed.
3-9-3 Manual setting of step-adjust
The AR8200 usually correctly ‘guesses’ what step-adjust you require, often this is a half step but manual
intervention is possible!
Example 2:
Assume that you wish to tune from 58.445 MHz in 15 kHz steps (i.e. 58.445, 58.460, 58.475,
58.490, 58.505 etc). When manually tuning, the AR8200 would normally correct the frequency display to
read 58.455 then step upward in 15 kHz steps. Tuning back downward will skip 58.445 MHz (the starting
point) as the original frequency was not divisible by step size… it was offset by +5 kHz. Usually the
frequency must be divisible by the tuning step size.
Section 3-9-1, 3-9-2, 3-93
- (1) AR8200 Index 1
- Section 1 1
- 1-1 Introduction 5
- 1-2 Take care of your radio 5
- Section 1-1, 1-2 5
- Section 1-2, 1-3 6
- 1-4 Accessories supplied 7
- Section 1-3, 1-4 7
- 1-5 Controls & functions 8
- Section 1-5 8
- 1-5-1 Keypad 9
- Section 1-5-1 9
- 1-5-2 Summary of keys 10
- Section 1-5-2 10
- 1-5-3 Side panel 15
- Section 1-5-3 15
- Section 1-6-1 17
- 1-6-2 Charging the NiCads 18
- 1-6-3 Cigar lighter lead 18
- Section 1-6-2, 1-6-3 18
- 1-6-4 Battery considerations 19
- Section 1-6-3, 1-6-4 19
- Section 2, 2-1 20
- 2-3 Fit the batteries 21
- Section 2-1, 2-2, 2-3 21
- 2-4-4 CLEAR key 23
- 2-4-5 MONITOR key 23
- 2-4-6 KEY LOCK 23
- Section 2-4-4, 2-4-5, 2-4-6 23
- Variable Frequency Oscillator 24
- Section 3-2 25
- Section 3-2, 3-3 26
- Section 3-3, 3-4, 3-5 27
- &Note: In AM and FM 28
- Section 3-5, 3-6 28
- 3-7 Changing receive mode 29
- 3-7-1 Auto-mode selection 29
- Section 3-7, 3-7-1, 3-7-2 29
- Section 3-7-2 30
- Section 3-7-2, 3-8 31
- Section 3-8 32
- 3-9 STEP-adjust 33
- Section 3-8, 3-9, 3-9-1 33
- 3-9-2 Cancelling step-adjust 34
- Section 3-9-1, 3-9-2, 3-93 34
- Section 3-93 35
- 3-10 FREQUENCY OFFSET 36
- Section 3-9-3, 3-10, 3-10-1 36
- Section 3-10-1, 3-10-2 37
- 3-11 Attenuator 38
- 3-12 Noise limiter 38
- Section 3-10-2, 3-11, 3-12 38
- Section 3-12, 3-13 39
- Section 3-13 40
- (4) VFO enhanced facilities 41
- 4-1 Quick memories 41
- Section 4, 4-1, 4-1-1 41
- VFO SEARCH 43
- Section 4-3-2, 4-3-3, 4-3-4 44
- Section 4-3-4, 4-3-5 45
- 4-3-6 Exiting VFO search 46
- 4-4 VFO environment menu 46
- 4-4-1 VFO SCAN 46
- 4-4-2 VFO search DELAY 46
- 5-1 Memory channel overview 51
- &Note: 51
- Section 5, 5-1 51
- Section 5-1, 5-2 52
- Section 5-2 53
- 5-4 Memory read “M.RD” 56
- Section 5-3, 5-4 56
- 5-5 Deleting memory channels 57
- Section 5-4-1, 5-5 57
- Section 6, 6-1, 6-2 60
- 7-2 SCAN considerations 62
- Section 7, 7-1, 7-2 62
- 7-3 Starting to SCAN 63
- Section 7-2, 7-3 63
- 7-4 Selecting a scan bank 64
- 7-5 Channel PASS 64
- Section 7-3, 7-3-1, 7-4, 7-5 64
- Section 7-5, 7-5-1, 7-5-2 65
- Section 7-7, 7-8 67
- 7-8-1 Scan DELAY 68
- 7-8-2 Scan LEVEL 68
- Section 7-8, 7-8-1, 7-8-2 68
- 7-9 Select scan 71
- Section 7-9-3, 7-9-4 72
- Section 7-9-4, 7-9-5 73
- (8) Search mode 74
- 8-1 Search types 74
- Section 8, 8-1, 8-1-1 74
- 8-3 Selection of search bank 76
- Section 8-2-4, 8-3 76
- Section 8-3 77
- 8-5-1 Search pass menu 80
- Section 8-5, 8-5-1 80
- Section 8-6, 8-7 82
- 8-7-1 Search DELAY 83
- Section 8-7, 8-7-1 83
- 8-7-7 Deleting search banks 87
- Section 8-7-7, 8-7-8 87
- (9) EDIT menu 88
- 9-1 EDIT COPY memory channel 88
- Section 9, 9-1 88
- (10) DELETE menu facilities 94
- Section 10, 10-1 94
- For example: 100
- (12) TEXT search and input 101
- 12-1 Text input menus 101
- Section 12, 12-1 101
- Section 12-2 102
- 12-2 Text search 102
- (13) SHORT CUT keys 103
- 13-1 Short cut menu access 103
- Section 13, 13-1 103
- 13-2 Short cut text entry 104
- Section 13-2 104
- Section 13-3 105
- (14) Configuration menu 106
- 14-1 CONFIG BEEP 106
- 14-2 CONFIG LAMP 106
- Section 14, 14-1, 14-2 106
- 14-4 CONFIG Power save 108
- Section 14-4 108
- 14-9 CONFIG Opening message 111
- Section 14-8, 14-9 111
- (15) Band scope 112
- 15-1 Starting the band scope 112
- Section 15, 15-1 112
- 15-8 Peak hold 114
- Section 15-10 115
- (16) Sleep ¹ 116
- Section 16 116
- (17) Option socket 117
- Section 17 117
- 17-1 RS232 operation 118
- Section 17-1, 17-2 118
- 17-2-1 How to clone data 119
- Section 17-2-1 119
- (18) Slot card socket 121
- 18-1 Optional slot cards 121
- 18-1-1 Fitting the slot card 121
- Section 18, 18-1, 18-1-1 121
- Section 18-1-1, 18-1-2, 18-2 122
- 18-3-1 CTCSS tone squelch 123
- Section 18-2, 18-3. 18-3-1 123
- 18-3-2 CTCSS search 124
- Section 18-3-1, 18-3-2 124
- «” will be displayed to 125
- Section 18-3-2, 18-4 125
- Section 18-4, 18-5, 18-5-1 126
- Section 18-6-1, 18-6-2 129
- Section 18-6-2, 18-6-3 130
- Section 18-6-4 131
- Section 18-6-7 134
- (19) Trouble shooting 136
- Section 19, 19-1, 19-2 136
- Section 19-2, 19-3 137
- (20) Optional accessories 138
- Section 20 138
- Section 21 139
- (22) Specification 140
- Section 22 140
- Fax: +81 3 3865 1697 141
- Downloaded by 142
- Amateur Radio Directory 142
Verwandte Produkte und Handbücher für Empfänger AOR AR8200
Empfänger AOR ARD9900 Bedienerhandbuch
(36 Seiten)
(36 Seiten)
Empfänger AOR AR2700 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Empfänger AOR AR16 Bedienerhandbuch
(108 Seiten)
(108 Seiten)
Empfänger AOR AR8600 Wartungshandbuch
(8 Seiten)
(8 Seiten)
Empfänger AOR AR8000 Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Empfänger AOR AR-Mini Spezifikationen
(49 Seiten)
(49 Seiten)
Empfänger AOR SR2200 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Empfänger AOR AR7030 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Empfänger AOR AR-ALPHA Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Empfänger AOR SDU-5000 Bedienerhandbuch
(39 Seiten)
(39 Seiten)
Empfänger AOR AR-3000A Bedienungsanleitung
(56 Seiten)
(56 Seiten)
Empfänger AOR AR2300 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Empfänger AOR AR7030 Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Empfänger AOR SDU-5000 Bedienungsanleitung
(43 Seiten)
(43 Seiten)
Empfänger AOR ARD-25 Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Empfänger AOR AR2300 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Empfänger AOR AR3030 Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Empfänger AOR AR7000 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Empfänger AOR WX2000 Betriebsanleitung
(40 Seiten)
(40 Seiten)
Empfänger AOR AR1000 Bedienungsanleitung
(7 Seiten)
(7 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.486 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern